A Provocative Rant About Fiat Panda Key Fob Replacement
Reasons Your Fiat 500 Key Fob Won't Work
A key fob from Fiat 500 is a convenient way to unlock the doors and start the car. However, there are numerous reasons why the fob won't be functioning. It could be due to a dead battery damage to the receiver module, issues, and interfering.
This listing is for an NEW replacement Fiat Flip Key Remote that looks like the Ilco brand. It has to be professionally programmed (click here to search for local locksmiths in the automotive industry). Includes trunk, lock and unlock buttons.
Dead Coin Battery
A dead battery is probably the most common reason for your 500 key fob that isn't working. Modern key fobs offer limited operating range and must be within a few inches of your vehicle to function. If you are further away from your vehicle, and you push the keyfob button it won't respond and display the message "Key Fob Not Detected".
If this occurs then replace the battery for your coin-cell (Part Number CR2032) by a brand new one of a trusted brand like Panasonic Duracell or Energizer. They are usually available at your local hardware store, or online.
After you've changed the battery on the coin cell It is possible to test it by standing next to your Fiat 500 and pressing the buttons. The parking lights will flash and the key fob will operate the lock and unlock switches.
If the fob's key doesn't work after replacing the battery, it could have water damage that prevents it from communicating with the receiver module in your vehicle. Water damage can occur in many ways, such as an easy splash or submerging your key fob in saltwater at the beach. If you suspect that your fob was exposed to water, put it in a dry rice bag to draw the moisture out. If this does not work, you'll have to get your fob reset by an auto locksmith or dealer.
Water Damage
Water damage can happen if you submerge the fob in the ocean, or wash it in a machine. Saltwater can be particularly harmful to the circuit board of the fob and can cause it to short out and eventually die. It's not a good idea to soak the fob in water, but don't give it up if you accidentally drop it in water, or fail to take it out of your pocket.
First take the battery off the fob. Before replacing the battery, clean the electronic chip with isopropyl or another similar product. Check the fob again to see if it is working. If the fob doesn't work, it may need to be programmed again. This is typically handled by a dealer or professional auto locksmith.
If your key is a bit older and is not programmed for your vehicle, you will need to replace it completely. This is an easy process which can be accomplished by a professional locksmith for automotive use. The locksmith will require the key to be cut to match your car's ignition. The locksmith will also have to reprogram your fob in the car's system. This is a cost-effective and quick process that can be completed within the same day.
replacement fiat 500 key fob www.thekeylab.co.uk of the most common reasons why your 500 key fob may stop functioning is because it's out of range. The remote usually has 30 feet of range or less and if it's far from your vehicle, it will not respond to your commands. You can remedy this by moving your remote closer to your car until it responds.
If your fob isn't working after you replace the battery in the coin, also known as a "button", "watch" or "button" or "button", it could be due to an issue with the circuit board inside. Reprogramming the fob typically resolves the issue. You can find instructions on how to do this for most automobiles by searching YouTube or consulting the owner's manual.
It may be necessary to replace the clips made of metal that hold the coin batteries in the correct position. If they lose tension, they could stop the coin battery from being seated properly and can cause the remote to malfunction.
In rare instances it is possible that the fob will become disconnected from your vehicle due to software or hardware issues. You can fix this problem by visiting your local dealer or auto-locksmith to reprogram your key fob. In some cases the software might need to be reinstalled in your body control modules.
Interference
In addition to a dead battery on a coin the key fob could not be receiving or transmitting a signal due to interference. This can happen when the key fob is close to the radio transmitter (cell phones, radar detectors) or any other source of electromagnetic radiation. Other reasons why the key fob could not function could be due to a weak connection to the buttons and internal chip, or water damage.
If your key fob suddenly stopped working, or you have tried everything at home to fix it (e.g. replacing the battery, reprogramming, and using the spare key fob, you might have a damaged receiver module on your 500. The receiver module is situated under the dash and is able to pick up the radio frequency signals from the key fob. It converts the signals into electronic commands that are then interpreted by the vehicle.
Fortunately, there's an easy way to reset every single system on board in your 500 keys, including the key fob. Disconnect the battery of 12 volts for about 15 minutes, by taking off the negative cable first then the positive cable. Reconnect the battery. This will get rid of any remaining electrical charge and restart the car's computers. This could allow you to the key fob to function again. If the issue persists you should seek out a certified technician. They will be able to identify the root of any problems.